Supportnet Computer
Planet of Tech

Supportnet / Forum / WindowsXP

Win Xp Pro Installations: Ntfs.sys Fehlermeldung





Frage

System: Asus P4C800-E Deluxe Western Digital Raptor - WD360GD S-Ata 10.000 U/Min Gainward Geforce Fx5900 Ultra 256 MB Kingston HyperX 2 x 512 MB DDR RAM PC 3200 400Mhz usw. Nur diese Festplatte verwendet an Sata 1 Anschluss auf Mobo. Bei der Installation von Win Xp Pro kommt folgende Fehlermeldung die unten exakt abgetippt ist. Verbleibende Installationszeit wären 37 Minuten gewesen, der Fehler kommt nach 3 Versuchen immer zu diesem Zeitpunkt. Blauer Hintergrund, weiße Schrift. Sobald diese Fehlermeldung einsetzt ist ein kurzes Klicken zu vernehmen. ----------------------------------------------------------------------------------------------- A problem has been detected and windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: Ntfs.sys PAGE_FAULT_IN_NONPAGED_AREA If this is the first time you´ve seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacurer for any windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching and shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup options, and then select Safe Mode. Technical information: *** STOP: 0x00000050 (0xF695FA30, 0x00000000, 0xF7681287, 0x00000000= *** Ntfs.sys - Adress F7681287 base at F7660000, DataStamp 3d6de5c1 Beginning dump of physical memory Physical memory dump complete Contact your system administrator or technical support group for further assistance. ---------------------------------------------------------------------------------------------------------------------------------- Ich restarte und bin wieder in der Installation bei 39 Minuten Restdauer. Nach kurzer Zeit kommt exakt diese Fehlermeldung wieder. Ich restarte und boote von Cd und befinde ich mich wieder im Anfangssetup von Win Xp Pro. Dort gehe ich auf INSTALL und sehe folgendes: ----------------------------------------------------------------------------------------------------- C: Partition1 [Ntfs] 35291 MB < 34682 MB free> Unpartitioned space 8 MB --------------------------------------------------------------------------- Ich quite, da ich nicht noch ein x-tes Mal Formatieren und neusinstallieren will, da die Fehlermeldung garantiert wieder auftritt. Neustart und bin wieder im Install Menü und etwas neues erscheint, ein Pop-Up Fenster: ---------------- Fatal error An error encountered that prevents Setup from continuing. Setup failed to install the product catalogs. This is a fatal error. The setup log files should contain more information. Press OK to view the Setup log file. -------------------------------------------------------- Ich bestätige und dies erscheint: ------------------------------------------------------------------------------------------------------------------------------------ Error: The signatur for Windows Xp Professionel Setup is invalid. The error code is 6ba. The RPC server is unavailable. *** Fatal error: Setup failed to install the product catalogs. This is a fatal error. The setup log files should contain more information. *** ------------ Ich schließe die Fehlermeldung, es wird neu gestartet. Nun kommt wieder die Blue Screen Fehlermeldung. Frustriert schalte ich aus :) Fazit: Muß ich wenn ich mit der Win Xp Pro Installation beginne und optional F6 drücken kann für Scsi und Raid Sachen zu installieren (?) F6 drücken und von Diskette einen Treiber für S-Ata installieren? Ich habe gehört dies ist bei S-Ata Platten notwendig. Welchen Treiber brauche ich hierfür und wo finde ich ihn und wie muß ich ihn installieren?

Antwort 1 von Poison

Eventuell ein Problem mit dem Arbeitsspeicher??

Gruss Poison

Antwort 2 von hallo1980

Hast du den einen lösungsweg gefunden?
hab nämlich das gleiche problem
Gemeint ist windows xp

Antwort 3 von PC-Help-2004

Bei der Inst. von Xp sollte immer dann die Diskette verwendet werden, wenn es sich um Raid oder S-ATA Treiber handelt. Sind auch bei guten Herstellern auf Diskette beigelegt. Wenn nicht, übers Internet vom Kollegen beim Hersteller Downloaden lassen.
Bevor mann dies macht, solte mann dann
Zusätzlich nen Arbeitsspeicher Test durchführen.
Nun
Install. wir Xp
bei zusatzlichen Treiber F2 Taste Drücken.
Nun wird man aufgefordert die Diskette mit dem Treiber einzulegen. Treiber auswählen für XP und weiter gehts.

Hoffe ja mal es hat geholfen.
Wenn nicht Melden.

Angaben ohne Gewehr.

Antwort 4 von PC-Help-2004

PS Sorry meinte Taste F6 und nicht F2.

Antwort 5 von hanspn

hi,

hab das gleiche problem... :(

nur aus dem laufendem betrieb herraus...

ein klick auf dem pakierkorb und ZACK... reboot..

> fehlermeldung

MFG hanspn

Antwort 6 von w489uw5z03

soo hab mich mal schlau gemacht:

bitte schön:
-----------------------------------------------------------------
Stop 0x00000050 or PAGE_FAULT_IN_NONPAGED_AREA
This Stop message, also known as Stop 0x50, occurs when requested data is not found in memory. The system generates a fault, which normally indicates that the system looks for data in the paging file. In this circumstance, however, the missing data is identified as being located within an area of memory that cannot be read to disk. The system faults, but cannot find, the data and is unable to recover. Faulty hardware, a buggy system service, antivirus software, and a corrupted NTFS volume can all generate this type of error.

Interpreting the Message
The four parameters listed in the message are defined in order of appearance as follows:

Virtual address which caused the fault
Type of access (0 = read operation, 1 = write operation)
If not zero, the instruction address which referenced the address in parameter 1
Opaque information about the stop, interpreted by the kernel
Resolving the Problem
Faulty hardware. Stop 0x50 usually occurs after the installation of faulty hardware or in the event of failure of installed hardware (usually related to defective RAM, be it main memory, L2 RAM cache, or video RAM). If hardware has been added to the system recently, remove it to see if the error recurs. If existing hardware has failed, remove or replace the faulty component. You should run hardware diagnostics supplied by the system manufacturer. For details on these procedures, see the owner´s manual for your computer.

Buggy system service. Often, the installation of a buggy system service is a culprit. Disable the service and confirm that this resolves the error. If so, contact the manufacturer of the system service about a possible update. If the error occurs during system startup, restart your computer, and press F8 at the character-mode menu that displays the operating system choices. At the resulting Windows 2000 Advanced Options menu, choose the Last Known Good Configuration option. This option is most effective when only one driver or service is added at a time.

Antivirus software. Antivirus software can also trigger this error. Disable the program and confirm that this resolves the error. If it does, contact the manufacturer of the program about a possible update.

Corrupted NTFS volume. A corrupted NTFS volume can also generate this error. Run Chkdsk /f /r to detect and repair disk errors. You must restart the system before the disk scan begins on a system partition. If the hard disk is SCSI, check for problems between the SCSI controller and the disk.
--------------------------------------------------------------
bei mir war es die kaputte platte...
mal mit wipe bearbeiten...

viel spaß..

Antwort 7 von schnikemike

Ich habe genau das die gleiche fehlermeldung und zwar auf 3 pcs! wärend der instalation von win 2000 pro und im laufendem betrieb von win xp pro.


Kennt jemand eien virus der soetwas macht.

ich habe bei mir antivirenkit 2005 (orginal) laufen das ständig aktuell ist (live update).

Aber das findet nix auch nicht über die boot cd.


Wenn es an den platten liegt. gibt es da ein tool welche das überpüfen kann.

Antwort 8 von Poly

Hallo,

Also, Windows XP verfügt über Raid Controller und SCSI Controller. Allesamt sind nicht immer 100% kompatibel zu dem, was der Hersteller des Raid Controllers vorgibt. Grundsätzlich ist bei Raid SATA ... ein Treiber des Mainboardherstellers immer die bessere Lösung. Bei einer Neuinstallation muß dieser Treiber beim Bootvorgang mit F6 eingebunden werden, damit XP die Platte am Raid erkennt. Will man das Laufwerk am Raid als Bootlaufwerk betreiben ist diese Maßnahme absolutes Muß sonst geht nichts. Im laufenden Betrieb verwendet XP den Controller des Mainboardherstellers ebenfalls, ist aber das Raid oder SatA Laufwerk kein Bootlaufwerk, so wird es von XP nach der Installation erkannt und mit XP-eigenen Treiber eingebunden. Ich empfehle aber dringend, den Original-Treiber des Herstellers zu installieren.

Vorrausgesetzt die Platte(n) am Raid sind nicht defekt, sollte eine Installation problemlos möglich sein.

Gruß
Poly

Ich möchte kostenlos eine Frage an die Mitglieder stellen:


Ähnliche Themen:


Suche in allen vorhandenen Beiträgen: